CANON LOW VOLTAGE BOOT ROM ADAPTER - #ACDM72A - $279.00
The Canon low voltage (LV) boot rom adapter supports the boot roms found in the latest ImageRunner machines with four digit model numbers (Example: IR3300, IR5000, IR7200). The adapter snaps into the socket on the AR-32A programming unit and supports both single and double chip assemblies. All boot rom sizes are supported including 4, 8, 16 and 32 meg parts (Example: 29LV160T). Each chip of a double chip assembly is selected using a slide switch to select CHIP 1 or CHIP 2. The ACDM72A allows you to erase and reprogram a corrupt boot rom or copy one boot rom to another (repurpose).

CANON 5 VOLT BOOT ROM ADAPTER - #AC8B72 - $279.00
The Canon 5 VOLT boot rom adapter supports the boot roms found in earlier ImageRunner machines with three digit model numbers (Example: IR400). The adapter snaps into the socket on the AR-32A programming unit and supports both single and double chip assemblies. All 5 volt boot rom sizes are supported including 4, 8 and 16 parts (Example: 29F080). Each chip of a double chip assembly is selected using a slide switch to select CHIP 1 or CHIP 2. The AC8B72 allows you to erase and reprogram a corrupt boot rom or copy one boot rom to another (repurpose).

CANON PARALLEL EEPROM/FRAM 28 PIN SURFACE MOUNT CLIP WITH INTERFACE - #ASOIC28/LV - $249.00
The ASOIC28/LV surface mount clip with interface supports surface mounted 28 pin parallel EEPROM and FRAM memory devices used in Canon copy machines to store count data. The ASOIC28/LV supports both 5 VOLT and Low Voltage parts using a switch on the interface board. The 28 pin surface mount clip fits over the 28 pin parallel memory part on any compatible counter assembly. The ASOIC28/LV allows you to read, copy, edit and program both the counter data plus the machine serial number.

RICOH FRAM COUNTER INTERFACE - #ARFCI - $139.00
The RICOH FRAM COUNTER INTERFACE package allows you to read, edit, program, copy and save the contents of four and eight chip Ricoh counter assemblies. The assembly incorporates the CABLE8/DD board, a custom short-wire 8 pin clip plus a precision fabricated, spike-jaw alligator clip which attaches to the CABLE8/DD. The CABLE8/DD attaches to the ASERSM1A (not included) which serves as the power source and signal interface. The ARFCI package operates by attaching the alligator clip spike to a specific location on the counter assembly. This enables access to the 8 pin serial FRAMs. The 8 pin clip is then attached to the desired chip on the counter assembly.

SHARP 5 VOLT FLASH ROM ADAPTER - #ASDM72A - $239.00
Specifically designed to support 5 volt the Sharp flash roms used in digital copiers, the ASDM72A adapter allow the EPROM+ system to erase, program and read the 8, 16 and 32 meg single and dual chip flash roms. This allows you to update these parts without using a copy machine to perform the programming. For normal Sharp S-Record (.MOT) files, the EPROM+ system performs the operation directly from downloaded files and creates the proper data formats for the OPE, PCU, ICU and Print Controller assemblies.
Supports Models: (C150/160/250/270) (280/285/287/335/337/507)

SHARP LOW VOLTAGE FLASH ROM ADAPTER - #ASDM72B - $239.00
Specifically designed to support low voltage Sharp flash roms used in digital copiers, the ASDM72B adapter allow the EPROM+ system to erase, program and read the 8, 16 and 32 meg single and dual chip flash roms. This allows you to update these parts without using a copy machine to perform the programming. For normal Sharp S-Record (.MOT) files, the EPROM+ system performs the proper conversion directly from downloaded files.
Supports Models: (350/450) (C260) (550/620)